G209 Screw pin anchor shackles meet the performance requirements of Federal Specification RR-C-271G Type IVA, Grade A, Class 2, except for those provisions required of the contractor. For additional information, see page 452. G-210 S-21/ 0 G-210 Screw pin anchor shackles meet the performance requirements of Federal Specification RR-C-271G

19010204 Recovery Shackle 3/4″ 4.75 Ton Red – Sold In Pairs

Side Loading Reduction Chart for Screw Pin and Bolt Type Shackles Only+ Angle of Side Load from Vertical In-Line of Shackle Adjusted Working Load Limit 0° – 5° In-Line* 100% of Rated Working Load Limit … For shackles larger than 125 metric tons, where the angle of the side load is greater than 5 degrees, contact Crosby

Source Image: hisenderrigging.en.made-in-china.com
Download Image

06.07.2004. CROSBY SHACKLE – LOAD CAPACITY TABLE. Crosby Shackle, Bolt Type (US Fed Spec Type IVA, Class 3), G-2130 & S2130. G-2130 S-2130. •. Working Load Limit permanently shown on every shackle. Capacities 1/3 thro 150 metric tons. •. Forged-Quenched and Tempered, with alloy pins.

Source Image: huyett.com
Download Image

1″ Super Strong Screw Pin Anchor Shackle 10 TON– Liftgear USA The proper application of shackles requires that the correct type and size of shackle be used. The shackle’s Working Load Limit, its size, a traceability code, and the manufacturer’s name should be clearly marked in the bow. Traceability of the material chemistry and properties is essential for total confidence in the product.

Source Image: baremotion.com
Download Image

Shackle Size And Capacity Chart

The proper application of shackles requires that the correct type and size of shackle be used. The shackle’s Working Load Limit, its size, a traceability code, and the manufacturer’s name should be clearly marked in the bow. Traceability of the material chemistry and properties is essential for total confidence in the product. For each size of shackle, there is usually a standard working load limit (i.e. 1/2″ shackles usually have a 2-ton working load limit). However, this is not regulated, so there are some non-standard shackles out there that have higher or lower working load limits than others. … Here is a chart that shows the dimensions of some common sized bow

Crosby® G-210 Screw Pin Chain Shackles – Baremotion

Dividing 5.1 by 3 gives 1.7. The square root of 1.7 is 1.30″. The proper size shackle will be the one just larger than 1.3″, in this case, the 1-3/8″ shackle. 1-3/8″ is equivalent to 1.375″. Here are a few more problems along with the vectored solutions. Dyneema® sheathed shackle® High-load M® HL | Nodus Factory

Source Image: nodusfactory.com
Download Image

Bulk Bolt Type Anchor Shackles – SICHwirerope Dividing 5.1 by 3 gives 1.7. The square root of 1.7 is 1.30″. The proper size shackle will be the one just larger than 1.3″, in this case, the 1-3/8″ shackle. 1-3/8″ is equivalent to 1.375″. Here are a few more problems along with the vectored solutions.

Source Image: sichwirerope.com
Download Image

19010204 Recovery Shackle 3/4″ 4.75 Ton Red – Sold In Pairs G209 Screw pin anchor shackles meet the performance requirements of Federal Specification RR-C-271G Type IVA, Grade A, Class 2, except for those provisions required of the contractor. For additional information, see page 452. G-210 S-21/ 0 G-210 Screw pin anchor shackles meet the performance requirements of Federal Specification RR-C-271G

Source Image: overlandvehiclesystems.com
Download Image

1″ Super Strong Screw Pin Anchor Shackle 10 TON– Liftgear USA 06.07.2004. CROSBY SHACKLE – LOAD CAPACITY TABLE. Crosby Shackle, Bolt Type (US Fed Spec Type IVA, Class 3), G-2130 & S2130. G-2130 S-2130. •. Working Load Limit permanently shown on every shackle. Capacities 1/3 thro 150 metric tons. •. Forged-Quenched and Tempered, with alloy pins.

Source Image: liftgear.com
Download Image

Anchor Shackle – Galvanized N223-669 | National Hardware CROSBY SCREW PIN SHACKLE DIMENSIONS G-209 & S-209 CARBON SCREW-PIN G-209 A ALLOY SCREW-PIN Nominal Size (in.) Working Load Limit (t)* G-209 Stock No. Weight

Source Image: national-hardware.com
Download Image

Extreme Max BoatTector Stainless Steel D Shackle – 7/8" 3006.8255 – The Home Depot The proper application of shackles requires that the correct type and size of shackle be used. The shackle’s Working Load Limit, its size, a traceability code, and the manufacturer’s name should be clearly marked in the bow. Traceability of the material chemistry and properties is essential for total confidence in the product.

Source Image: homedepot.com
Download Image

Our entire range of Lyre Shackles – Levage Manutention For each size of shackle, there is usually a standard working load limit (i.e. 1/2″ shackles usually have a 2-ton working load limit). However, this is not regulated, so there are some non-standard shackles out there that have higher or lower working load limits than others. … Here is a chart that shows the dimensions of some common sized bow

Source Image: levagemanutention.com
Download Image

Bulk Bolt Type Anchor Shackles – SICHwirerope

Our entire range of Lyre Shackles – Levage Manutention Side Loading Reduction Chart for Screw Pin and Bolt Type Shackles Only+ Angle of Side Load from Vertical In-Line of Shackle Adjusted Working Load Limit 0° – 5° In-Line* 100% of Rated Working Load Limit … For shackles larger than 125 metric tons, where the angle of the side load is greater than 5 degrees, contact Crosby

1″ Super Strong Screw Pin Anchor Shackle 10 TON– Liftgear USA Extreme Max BoatTector Stainless Steel D Shackle – 7/8" 3006.8255 – The Home Depot CROSBY SCREW PIN SHACKLE DIMENSIONS G-209 & S-209 CARBON SCREW-PIN G-209 A ALLOY SCREW-PIN Nominal Size (in.) Working Load Limit (t)* G-209 Stock No. Weight